Service call

HVAC Maintenance

Routine AC maintenance for ductless mini split

Routine AC and Heat maintenance

Routine AC maintenance

I repaired a Goodman GSX16 heat pump this afternoon. The problem was a seized condenser fan motor. I replaced the motor with a new ECM model, installed a fresh capacitor, and verified proper amperage draw. After cleaning the condenser coils with Nu-Calgon coil cleaner, I tested the system's heating and cooling modes for optimal operation.

I performed duct sealing on a residential HVAC system today. Using Hardcast foil-grip tape and mastic sealant, I sealed all accessible joints and seams in the ductwork. I also installed new R-8 insulation on exposed ducts in unconditioned spaces. A duct blaster test confirmed significant reduction in air leakage, improving system efficiency.

I repaired a Rheem Prestige RA20 air conditioner this afternoon. The problem was a faulty compressor contactor. I replaced it with a new heavy-duty contactor and cleaned the condenser coils using Nu-Calgon Evap-Fresh. After recharging with R-410A and adjusting the TXV, the system now operates at peak efficiency.

Today, I installed a Carrier Performance 16 heat pump. I set up the outdoor unit, connected the lineset, and installed a new air handler with a variable-speed blower. I flushed the existing lineset, installed a bi-flow filter drier, and charged the system with R-410A. The Carrier Côr 7C thermostat was programmed for optimal performance.

I replaced a faulty condenser fan motor on a Rheem RA16 air conditioner. After disconnecting power, I removed the old motor and blade assembly. I installed a new OEM ECM motor, ensuring proper mounting and alignment. I connected the wiring according to the diagram and replaced the capacitor with a 5 MFD run capacitor. After reassembly, I verified correct rotation, amperage draw, and airflow. I then tested the system's operation, confirming proper cooling performance and efficient heat rejection from the condenser coil.

Repaired an AC system in Woodbridge Township by replacing a malfunctioning TXV (Thermostatic Expansion Valve) on a Daikin DX16TC unit. The system was not cooling effectively, so I replaced the valve and recharged the unit with R-410A refrigerant. Tested the system to ensure proper temperature control and efficient operation, restoring full cooling capacity.

Routine AC maintenance

Conducted thorough maintenance on Trane XR14 air conditioning system. Cleaned condenser coils with Viper Coil Cleaner. Verified refrigerant charge using Testo 550s digital manifold. Replaced 45/5 MFD dual run capacitor with TITAN PRO TOCF45. Flushed condensate line with BioFresh. Inspected ductwork for leaks using FLIR ONE Pro thermal camera. Replaced air filter with MERV 13 Nordic Pure. Calibrated Nest Learning Thermostat. System now operating at optimal efficiency.

Replaced faulty blower fan motor in a Carrier 59SC5A furnace at Woodbridge Township residence. Diagnosed issue using Fluke 87V multimeter, confirming motor failure. Installed new Genteq 3/4 HP ECM motor (5SME39SL0310) for improved efficiency. Upgraded capacitor to Mars 12010 run capacitor. Calibrated motor using GE TECMate Pro software for optimal performance. Cleaned blower wheel with Simple Green to remove debris. Verified proper amperage draw and CFM output using Testo 417 anemometer. System now operates quietly with enhanced airflow, ensuring consistent heating and cooling throughout the home.

Performed AC service in Woodbridge Township for Edison Heating and Cooling. Checked refrigerant pressures, cleaned condenser coils, and replaced the air filter. Tested the thermostat calibration and inspected the blower motor and capacitor. Verified all electrical components and connections. The system is now optimized for efficiency and reliability, ensuring consistent cooling performance.

Responded to a call regarding an air conditioning unit with a faulty blower. Performed diagnostic tests and identified the issue as a failed blower motor assembly. Followed proper lockout/tagout procedures and disconnected power to the indoor air handler unit. Removed the existing blower motor and installed a new direct-drive replacement rated for the specified CFM and static pressure requirements. Realigned pulleys, secured belt tensioner, and validated proper rotation. Enabled system restart and confirmed adequate airflow across the evaporator coil. Verified the unit was operating within designed temperature split and refrigerant pressures. Blower motor replacement restored designed airflow for efficient cooling.

Service by Edison Heating and Cooling

Service by Edison heating and cooling

Ac maintenance

AC Maintenance

Ac maintenance

Ac maintenance

During a recent AC maintenance visit, I cleaned the condenser coils, replaced the air filter, and checked the refrigerant levels to ensure optimal cooling efficiency. I also inspected the electrical connections and tested the thermostat for accuracy. This preventative maintenance is crucial for enhancing the system’s reliability and performance throughout the cooling season.

SEASONAL AC MAINTENANCE

While servicing a Goodman GSX16 HVAC unit, a significant issue was identified with the blower motor, which was not operating at its intended capacity, leading to inadequate air circulation throughout the premises. Upon further investigation, the capacitor, crucial for motor startup and operation, was found to be failing. Both components were promptly replaced with compatible, high-quality parts. Additionally, a thorough cleaning of the unit’s interior was conducted to remove any debris that could impede performance, ensuring the system now runs smoothly and efficiently.